Loading... Please wait...

New Steel Squirrel Silhouette Target

Hover over image to zoom

  • Image 1
  • Image 2
$15.99
SKU:
107
Shipping:
Calculated at checkout

 Product Description

New Steel Squirrel Silhouette Target

These types of targets are a lot of fun, they even have a nice rewarding ring when shot.
These targets are designed to where a .22 LR will knock them over at 100 yards.
This Target will last a life time.

.22 Rifle or Handgun Target
Weight approx. 4.5 lbs each
New Unused
1/4" A36 Plate Steel

STEEL TARGETS: SAFETY AND USE

From the FBI Training Bulletin

There are many steel targets on the market allowing for a wide range of firearms training techniques. However, many of these targets do not provide adequate protection from bullet splatter so accidents can occur. It is important that the user know what factors make training on steel targets as safe and effective as possible.

When shooting steel targets, a “splatter zone” appears. This zone is the area in which the great majority of bullet fragments eventually wind up. The total amount of splatter in this zone is primarily dependent on the following four key issues: 1) Angle of deflection, 2) Bullet design and 3) Target placement.

ANGLE OF DEFLECTION

The type and design of a steel target determines the angle of deflection. As the bullet shatters on impact, the majority of the fragments spread out at 20-degree angles from the plate surface. This area, which forms thin triangular shapes to the left and right of the target, is referred to as the “splatter zone.” It is not a safe place to be as a full 95% of all bullet fragments can end up here.

BULLET DESIGN

A high quality, higher power factored ammunition is essential to reduce splatter. Simply stated, to minimize the size and pattern of splatter, drive the projectile harder. Consequently, a lead bullet with a low velocity is the worst option for steel target training. For safe training, it is recommended that only higher power factored bullets be used. A desirable round to produce consistent splatter is a jacketed hollow-point with a velocity of 1225 fps. Another issue is the “correlation factor.” This generally refers to how well a bullet holds together to give controlled expansion and penetration. In the case of steel target training, the best bullet is a frangible style round. The high velocity, frangible design of such bullets creates a predictable shattering effect on impact.

TARGET PLACEMENT

Even with the best targets and bullets, training can be dangerous if targets are placed incorrectly. Metal targets should not be placed parallel to each other with out a barrier between them. Splatter from one target could ricochet off another target (secondary splatter), and return to the shooter. Metal targets that are used in a grouping pattern should be staggered so as not to be in the 20 degree angle of deflection splatter zone of another target. Placing plywood to the sides of each target easily solves both of these problems. Because the wood is soft, it will absorb the splatter and not cause dangerous secondary splatter. The wood will, however, need to be replaced frequently to be an effective barrier. Another cause of secondary splatter can be large rocks or concrete. The best surfaces are made of sand or fine gravel. If concrete is used, it should be covered by wood or pea gravel.

OTHER SAFETY ISSUES

Since splatter can only be minimized and never totally eliminated, proper eye protection must be mandatory on all firing ranges. Eye protection should be OSHA tested and have side protection built in. Long sleeves and hats are optional but recommended. Instructors and observers should stand behind the shooter and obey all safety precautions as well. In short, training on steel targets can be safe if done properly.

 
General Warnings:
SAFETY RULES FOR SHOOTING STEEL TARGETS:
1. Always Keep The Muzzle Pointed In A Safe Direction.
2. Don't Rely On Your Guns Safety.
3. Be Sure Of Your Target and What's Beyond It.
4. Use Correct Ammunition.
5. Do not fire high powered rifles at targets closer than 100 yards.
6. Do not fire small bore guns at targets closer than 40 yards.
7. Minimum recommended distance with a handgun and standard lead ammunition is 15 yards.
8. Do not fire air guns at targets closer than 12 yards.
9. Always wear wrap-around eye protection and proper hearing protection.
10. Discontinue use of target if it becomes disfigured, deformed, or damaged in any way.
11. Never ever use armor-piercing, steel-core, or other hardened ammunition.
12. Never ever use steel shot, pellets, BB’s, or other air gun projectiles.
13. Never use ammunition that exceeds the target’s scope of design.
14. Always use high quality steel targets specifically designed for heavy duty use.
15. Never use steel targets for purposes outside their scope of design.
 
General Disclaimer:
 
Buyer assumes all responsibility for the use and misuse of the targets purchased.
CARDINAL RULES OF FIREARMS SAFETY:
1. Treat all firearms as though they are loaded.
2. Point the muzzle in a safe direction at all times.
3. Keep your finger outside the trigger guard until you are on target and have decided to fire.
4. Be sure of your target and what is beyond it.
5. Keep target low to the ground and/or use a backstop to stop stray bullets.

Questions or Quotes!
Email us at sales@qualitytargets.com

Quality Targets
204 E. through St.
Iola, Illinois 62838
Phone: 1-618-245-6515

 Find Similar Products by Category

Vendors Other Products

 Product Reviews

  1. T. Review

    Posted by quarterback on Nov 27th 2018

    Nice target cut great


  2. Squirrel Silhouette Target

    Posted by Julie on May 12th 2018

    Thanks for this one also.


  3. I like this product

    Posted by MichaelI on Mar 14th 2018

    This product is really good.


You Recently Viewed...

What's News

newsletter

Follow us on

Copyright 2024 Quality Targets Inc. All Rights Reserved.
Sitemap | BigCommerce Premium Themes by PSDCenter

Click the button below to add the New Steel Squirrel Silhouette Target to your wish list.